Epson printer support full#

Epson printer support full#

The display changes as shown below when the waste ink bottle is nearly full or an error occurs. Introductio n 20 5 Waste ink bottle status Displays the approximate amount of space availabl e in the waste ink bottle. The selected platen gap is shown as foll ows. When R IP Settings is selected, 0 will be displayed. Introductio n 19 If a media setting bank number creat ed with this printer is se lected as the print media, the number (from 1 to 30) will be displayed. To release the pause status, press the W button ag ain, or select Pause Cancel on the screen and then press the Z button. Introductio n 18 Understanding the Display 12 W button (pause/cancel button) The printer enters pause status if this is pressed while printing. Introductio n 17 3 M button (media setup button) Press this button to displa y the Media Setup menu, which contains such items as Media Remaining, Select Media, Customize Settings, and Print Media List. 2 P light (power light) The printer's operational status is indicated by a lit or flashing light. 1 P button (power button) Turns the power on and off. Introductio n 16 Control Panel 7H a n d l e After placing media on the right roll holder, rotate the handle to apply pressure to the roll core. 8W i p e r The wiper removes ink from the print head nozzles. Introductio n 15 Back 7C a p s Except during printing, these caps cover the print head nozzles to prevent them from drying out. 1 Print head The print head prints by moving left and right while emitting ink. Regularly clean or replace these parts as described in the chapters li sted in the reference sections below. Introductio n 14 Interior Dirt on any of the follo wing parts may reduce print quality. 2 Data lamp (orange) Indicates the network connection status an d whether the printer is receiving data. Use a shielded tw isted pair cable (category 5 or higher). Introductio n 13 LAN port 1R J - 4 5 c o n n e c t o r Connects the LAN cable. 2I n k i n l e t c o v e r Open this cover to refill the ink tank with ink. See РІР‚СљChip Unit Replacement and Ink RefillsРІР‚Сњ on page 104. Introductio n 12 Slider (chip holder) 1S l i d e r Attach the chip unit included with the ink pack before refilling the ink. 22 AC inlets #1 an d #2 Connect the power cables. Check the message on the control panelРІР‚в„ўs screen. Introductio n 11 21 Chip unit check lamp This lamp turns on when a message related to the chip unit is displayed. 6 Roll core holder locking screw The locking screws keep the roll core holders in place once they have been attached to the roll core. SeeРІР‚СљMedia Loading and Take-UpРІР‚Сњ on page 48. There are two holders: one on the left and one on the right. Introductio n 10 5 Roll core holder Place an empty roll core for media take-u p on these holders. It is normally clos ed wh en the printer is in use.

Front 1 Maintenance cover (left) Open this cover to clean the area around the print head. Introduction 9 Printer Parts Your product may look different fr om the illustrations in this guide, but the instructions are the same. РІСњРЏ If fluid is swallowed, do not force the pe rson to vomit, and c onsult with a physician immediately.

РІСњРЏ If fluid enters your mouth, c onsult a physician immediately. Failure to observe this precaution could result in bloods hot eyes or mild inflammation. Introduction 8 РІСњРЏ If fluid enters your eyes, ri nse immediately with water. Also, make sure the total ampere ra ting of all devices plugged into the wall outlet does not exceed the wall out letРІР‚в„ўs ampere rating. Introduction 7 РІСњРЏ If you use an extension cord with this produc t, make sure the total ampere rating of the devices plugged into th e extension cord does not exc eed the cordРІР‚в„ўs ampere rating. When choosing a location for this product РІСњРЏ Place this product on a flat, stable surface t hat is larger than th is product. Also be sure to follow all warnings and instructions marked on the printer.

Introduction 6 Chapter 1 Introduction Important Safety Instructions Read all of these instructions before using the printer. 130 When a Maintenance Call/Service Call Occurs. Р”В¬ontents 5 Chapter 5 Problem Solver When a Message Is Displayed. 64 Saving Optimal Settings for the Current Media (Print Media Settings). 6 When choosing a location for this product. No part of this publication may be reproduced, st ored in a retrieval system, or transmit ted in any form or by any mean s, electronic, mechan ical, photocopyi ng, record ing, or otherwise, with out the prior wr itten permission of Sei ko Epson Corpor ation.Р”В¬ontents 3 Contents Chapter 1 Introduction Important Safety Instructions. Copyrights and Trademarks 2 Copyrights and Trademarks All rights reserved.